Hand Pruners Buying Guide - Find the Best Pruners

Choosing the right hand pruner for the job is important. Usually, the type of pruner is a matter of personal preference. There are, however, some advantages to the different styles available at A.M. Leonard. Our Hand Pruners Buying Guide helps you find the hand pruner you need to get the job done.

Link to 1

This guide also covers pruner maintenance, sharpening, and pruner techniques. A properly maintained pruner lasts longer and makes better cuts! Mastering pruning techniques can help plants put on new growth AND improve flower and fruit production. Read our maintenance, sharpening, and technique tips below!

Finding the Best Hand Pruner

Types of Pruners

Bypass: Bypass pruners are the best choice for cutting live wood. The cutting blade &#;passes by&#; the counter blade in a scissor-like action. The hook shape of the counter blade helps hold the branch steady while cutting. The counter blade slightly crushes the bottom of the branch. Cut from the side of the branch that allows you to position the counter blade under the wood you intend to remove. This lessens the damage caused to the branch. Shorter blades make precision cuts easier, but longer blades give you a little more reach. A greater handle length increases leverage.

Anvil: Anvil-style pruners are the best choice for cutting old, hard, brittle and dead wood. The cutting blade drops into the middle of the anvil, sometimes into a small slot that receives the blade. The anvil supports the branch underneath to reduce the chance of it splintering. The anvil slightly crushes the bottom of the branch on either side of the cutting blade. It is therefore best to use an anvil-style pruner on dead wood.

Double Cut: Some people prefer a &#;double cut&#; style of pruner. A double-cut pruner has two cutting blades instead of an anvil or counterblade. The sharp edges of the blades are on opposing sides, so the cutting surfaces do not contact one another. The blades of double-cut pruners nest together.

Types of Handles

There are many pruner handle types and shapes available. There are handles designed for left-handed users and for someone with smaller hands. Ratcheting action can multiply cutting power, but can take several squeezes to make a cut. There are latches positioned in different places along the handle. A nice feature is a latch you can open with just one hand. Rotating and ergonomic handles offer added comfort and reduced blistering for prolonged pruning.

Choosing the Right Cutting Capacity

A pruner&#;s cutting capacity is the distance between the blades. This measurement does not indicate the size of branch that you can cut. True cutting capacity depends on the hardness of the wood and the strength of the user. If a cutting capacity is .75 inch, you may be able to cut that size linden without any problem. Unless you are unusually strong, you are not going to be able to cut through .75 inches of dead white pine. If you have to strain to make cuts, it can result in ragged cuts and cause damage to the pruner by twisting it. In this case, consider moving to a lopper or saw to prevent unnecessary damage.

The Best Hand Pruner Brands

A.M. Leonard

Pruner Brand Type Handle Type Cutting Capacity Replacement Parts ART17 Leonard Double Cut Stationary 1-Inch YES A10 Leonard Bypass Stationary 1-Inch YES Leonard Bypass Ergonomic 1-Inch YES Leonard Bypass Stationary 1-Inch YES Leonard Bypass Ergonomic 1-Inch YES Leonard Bypass Stationary .75-Inch YES Leonard Bypass Stationary .5-Inch YES 834 Leonard Bypass Stationary .75-Inch YES

ARS

Pruner Brand Type Handle Type Cutting Capacity Replacement Parts 120DX ARS Bypass Stationary .75-Inch YES ARS6 ARS Bypass Stationary, Small Hands .75-Inch YES

Bahco

Pruner Brand Type Handle Type Cutting Capacity Replacement Parts PXRM2 Bahco Bypass Ergonomic, Rotating .75-Inch YES PXL3 Bahco Bypass Ergonomic 1.25-Inch YES PXM2 Bahco Bypass Ergonomic .75-Inch YES

Corona

Pruner Brand Type Handle Type Cutting Capacity Replacement Parts 830CO Corona Bypass Stationary 1-Inch YES 80CO Corona Bypass Stationary 1-Inch YES 8COR Corona Bypass Stationary, Small Hands .5-Inch YES 60CO Corona Bypass Stationary .75-Inch YES

Felco

Pruner Brand Type Handle Type Cutting Capacity Replacement Parts 7FEL Felco Bypass Rotating, Right Handed 1-Inch YES 10FEL Felco Bypass Rotating, Left Handed 1-Inch YES 13FEL Felco Bypass Stationary, Extended 1.2-Inch YES 100FEL Felco Cut-and-Hold Bypass Ergonomic .4-Inch YES 12FEL Felco Bypass Rotating, Small Hands .8-Inch YES 8FEL Felco Bypass Ergonomic 1-Inch YES 9FEL Felco Bypass Ergonomic, Left Handed 1-Inch YES 11FEL Felco Bypass Ergonomic 1-Inch YES 6FEL Felco Bypass Stationary, Small Hands .8-Inch YES 31FEL Felco Anvil Stationary, Large Hands 1-Inch YES 2FEL Felco Bypass Stationary 1-Inch YES 4FEL Felco Bypass Stationary 1-Inch YES 5FEL Felco Bypass Stationary 1-Inch YES 300FEL Felco Bypass Stationary .4-Inch NO

Other Brands

Pruner Brand Type Handle Type Cutting Capacity Replacement Parts RP702 EZ KUT Anvil Ratcheting 1.5-Inch NO 19T1 Gilmour Anvil Stationary .625-Inch NO OK103 Okatsune Bypass Stationary .75-Inch YES OK101 Okatsune Bypass Stationary 1.25-Inch YES

Pruner Sharpening and Maintenance Tips

Below you can find helpful tips from our experts on how to sharpen and maintain your hand pruners. Proper maintenance results in your pruners lasting for years to come:

• Always use sharp pruning tools. They cut with less effort and the clean cuts &#;heal&#; faster
• Use a smooth, single-cut mill file or stone on straight edge pruning shears. The 10SS - Swiss Sharpener or OK6 - Okatsune Sharpening Stone are the best tools for sharpening pruning shears during assembly
• Sharpen your blade before it gets dull to reduce effort. Take your file or your stone in the field with you and touch up the blade as necessary. Use a can of WD-40 to loosen sticky pruners
• If a cutting blade is extremely dull, or notched, you may have to take the pruners apart to repair the damage. In some cases, it is easier to buy a new blade rather than attempting to repair a badly damaged one
• Maintain the factory angle on the cutting edge. Filing the blade too flat or too thin removes the bevel. With no bevel, the edge dulls quickly. A dull blade can chip or roll
• Sharpen away from, not toward, the blade
• Do not sharpen the anvil. Only sharpen the blade
• Sharpen a bypass pruner on just one side of the blade. Avoid filing the flat side of the blade, except to remove any burrs formed from filing the edge side. A wire brush may suffice in removing the light burrs that may appear
• Sharpen anvil and double-cut pruners on both sides of the blade
• Use one straight motion when sharpening. Do not "scour" back and forth as this heats the edge
• Hooks or notches on straight-edge shears rarely need sharpening
• You can sharpen wavy edge hedge shears with a tubular, fine stone or tubular file. Do not use a file with a flat side, as it does not follow the wavy contours of the edge
• After sharpening, apply light machine oil to the entire blade
• Store your pruning equipment in a protected environment
• A turbo-cut saw is very difficult to sharpen. It is less trouble to simply replace the blade
• Impulse-hardened saw blades cannot be sharpened

Pruning Techniques

For gardeners who cannot wait to get outdoors and begin working, late winter and early spring are great times to prune. These are the best pruning times as trees and shrubs have yet to put on new growth. An exception to this rule is for shrubs that flower in early spring, such as lilac or forsythia, which you should prune as soon as they have finished flowering. Ideally, complete this pruning before the plants set seed.

It is essential to choose the right pruner for the job. If you have to strain to make a cut with your pruner, then the pruner is too small. Improper pruning can result in ragged cuts and possible damage to the tool. Do not twist the pruning shear; instead open the cut on the branch. Bend the branch away from the cut to open it and make room for the cutting blade. Here are some more tips to get you pruning like a pro:

• Use hand pruners for branches no larger than the size of your little finger
• Do not use loppers for branches larger than the size recommended by the manufacturer. You may not be able to prune to the full maximum thickness, depending on the hardness of the wood
• When using bypass pruners, the anvil should be on the side of the branch you intend to remove. This helps avoid crushing the branch collar
• Use sharp tools to ensure good cuts and encourage callousing. If you suspect disease is present, clean your tools between cuts
• When pruning larger branches with a saw, undercut first to avoid causing damage the tree. Use the &#;3-cut&#; technique
• Beware of overhead utility lines when using a pole pruner or when you are on a ladder
• Pruning without a good reason may do more harm than good. If you are confused about which branches to remove, start with branches that are: 1) broken or dead; 2) diseased or dying; 3) rubbing or crossed; 4) growing toward the center of the plant
• In most cases, the only reason for pruning paint is to hide your cuts
• In a Midwest climate, it is best to avoid any elective pruning from August until we have had a hard frost. The natural response to pruning is growth, and new growth initiated late in the growing season will not be winter hardy.
• Evergreens should not be pruned during sub-zero weather. It is best to prune pines when the buds are in their candle stage. Spruce and fir are best pruned when the buds are dormant
• Avoid pruning three tree species until they leaf out: walnut, maple and birch. If they are pruned earlier, they "bleed" excessive sap. "Bleeding" does not hurt a tree, but it may stain the bark. It is safe to prune all other trees before leafing out
• You can do light pruning at any time. Broken, dead, weak, or heavily shaded branches can be removed at any time of the year with little effect on a plant
• Remember to step back and look at the plant while pruning to get the big picture
• Rejuvenating an overgrown flowering shrub like a lilac is a simple process. This process, however, must be done in stages over several years. Most lilacs send up lots of new shoots from the base of the shrub each season. Look at the base of your plant to see if new shoots are being sent up from below the ground. A process referred to as suckering. Right after it finishes blooming, prune out a quarter to a third of the oldest, woodiest stems. Make your cuts an inch or two from the ground. You can also shape the remaining top-wood now. In response, the lilac sends even more sucker stems. Repeat this process yearly and within a few years you will have a whole new plant that is much more compact and productive
• Avoid removing more than one-third of a plant in a season
• The narrower the angle of a branch, the weaker the crotch
• Flush cuts can delay healing and allow decay into the tree. Avoid cutting into the branch collar
• While young trees and shrubs can readily replace pruned tissue, older trees may not. Avoid thinning of branches on older, established trees

Learning More About Pruning and Buds

It helps when pruning to understand a little about buds. Here is a brief overview:

• Almost all growth comes from buds
• Buds can grow into leaves, branches or flowers
• There are several types of buds: dormant, latent and adventitious
• Dormant buds formed last season for this season&#;s growth
• Latent buds are there, but remain inactive, like an insurance policy
• Adventitious buds are those that quickly form in response to a need. These buds are not "deeply rooted" and result in weak growth
• Terminal buds are buds located at the tips. Lateral buds are buds located on the sides
• Terminal buds give off a hormone (auxin) that suppresses other growth. This process is &#;apical dominance&#; and it organizes the growth of a plant
• Besides pruning for safety, or to enhance the health of the tree, pruning can also improve flower and fruit production
• Pruning off the terminal buds removes the hormone that delays the lateral growth. This process results in a bushier, fuller plant
• Prune 1/4 to 1/2 an inch above the bud that you intend to use to direct future growth. Angle your cut away from the bud.

The keys to pruning trees and shrubs are a basic understanding of pruning techniques and knowing when to prune plants. For more information on these topics, check out the additional resources below. 

But it&#;s also important to understand the variety of tools available to make the job easier and use them correctly. The best tool for the job is determined by the size of the plant material to be removed and its location.

Hand Pruners
Hand pruners or pruning shears are generally used for cutting branches up to 3/4 inch in diameter. There are two basic types of hand pruners. Scissor-types have curved blades that overlap (scissor action) when making the cut. Anvil-type pruners have a sharpened upper blade which cuts against a flat surface (anvil). Each type is available in different sizes.

Choose the right pruning tool for the job, based on the location and size of the branch to be removed. Joseph O&#;Brien, USDA Forest Service, Bugwood.org.

Generally, scissor-type hand pruners are preferred over the anvil-types. Sharp, properly used scissor-type pruners make close, clean cuts. Anvil-types can&#;t cut as close as scissor-types and are more likely to crush stems when pruning.

Attempts to prune branches larger than 3/4 inch in diameter with hand pruners often results in torn, jagged pruning cuts and may damage the pruning shears.

Pole pruners make it easier to reach higher in a tree and can be used to cut larger branches up to 2 inches in diameter. Pole pruners consist of a stationary hook and hinged blade operated by a rope and mounted on a long wooden or fiberglass pole.

Loppers
Lopping shears, sometimes called secateurs, consist of blades attached to long handles, and are available in both bypass and anvil styles. The long handles give the gardener greater leverage so cuts can be made through larger branches. Lopping shears are also excellent for pruning difficult-to-reach places.

Additional features to look for include telescoping handles and ratcheting, geared or compound mechanisms. Models with telescopic handles can be extended to reach even higher into the plant. Ratcheting loppers make cuts in several steps. As the handles are compressed, the ratcheting mechanism holds the blades in place, enabling the gardener to release then squeeze again. Ever-increasing pressure is held on the branch until the final cut is made.

If you want to learn more, please visit our website Pruning Tools Manufacturer.

Compound loppers have a pivot-arm mechanism with amplifies the cutting force applied by the gardener. Geared loppers also increase the gardener&#;s cutting power, but utilize a geared mechanism. Both geared and compound loppers typically remove a branch in one cut.

Branches from 3/4 to 1 1/2 inches in diameter can be effectively cut with lopping shears.

Pruning Saws
Use a pruning saw on branches larger than 1 3/4 inches in diameter. Various types of pruning saws are available, including hand saws and pole saws.

When removing branches with a saw, use the 3-cut method to prevent ripping bark and damaging the tree. Joseph O&#;Brien, USDA Forest Service, Bugwood.org.

Small tree branches that are hard to reach from the ground can be pruned with a pole saw or pole pruner. A pole saw is essentially a saw blade attached to a long pole. Both pole saws and pole pruners can be used to cut branches up to 2 inches in diameter.

Chain saws are often used by professional arborists when cutting large tree branches. Chain saws, however, can be extremely dangerous to individuals with little experience or skill operating these machines. To reduce the risk of injury, home gardeners should use pruning saws rather than chain saws when pruning trees.

When removing branches with a saw, use the 3-cut method to prevent ripping bark and damaging the tree. 

In potentially hazardous situations, such as the pruning of large branches high in the tree or limbs near power lines, always contact a trained arborist!

Hedge Shears
Another tool sometimes used by the home gardener is the hedge shears. Hedge shears (manual or electric) are used to shear formal hedges to a definite size and shape. They should not be used to prune trees and shrubs.

When buying pruning equipment, choose high quality tools. Although high-quality tools are not inexpensive, if they are used and cared for properly, they will perform better and far outlast the poor quality, less expensive choices.

For more information on pruning techniques and timing, check out the resources below.

Feature image &#; A well-done pruning cut on a small branch. Joseph O&#;Brien, USDA Forest Service, Bugwood.org.

Share this:

• Twitter

• Facebook

Like

Loading...

Related

For more information, please visit Hedge Shears Supplier.